Refer to the exhibit. An engineer must ensure that all traffic leaving AS 200 will choose Link 2 as the exit point. Assuming that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers, which configuration accomplishes this task? A. R4(config-router)bgp default local-preference 200 B. R3(config-router)bgp default local-preference… Read More »
A. TLOC B. RLOC C. DNS D. VTEP E. EID Answer: Option B, E. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_lisp/configuration/xe-3s/irl-xe-3s-book/irl-overview.html Show AnswerDiscussion The post Which two namespaces does the LISP network architecture and protocol use? (Choose two. appeared first on Majanto.
A. Oracle VM VirtualBox B. Microsoft Hyper-V C. VMware server D. VMware ESX E. Microsoft Virtual PC Answer: Option B, D. Explanation: Reference: https://phoenixnap.com/kb/what-is-hypervisor-type-1-2 Show AnswerDiscussion The post Which two entities are Type 1 hypervisors? (Choose two.) appeared first on Majanto.
A. two-tier B. Layer 2 access C. three-tier D. routed access Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post A company plans to implement intent-based networking in its campus infrastructure. <br>Which design facilitates a migration from a traditional campus design to a programmable fabric design? appeared first on Majanto.
Refer to the exhibit. Assuming the WLC’s interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic? A. the controller management interface B. the controller virtual interface C. the interface specified on the WLAN configuration D. any interface configured on the WLC Answer: Option… Read More »
A. load balancing of unequal-cost paths B. load balance over four equal-cost paths C. uses interface bandwidth to determine best path D. per-packet load balancing over multiple paths Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post Which feature of EIGRP is not supported in OSPF? appeared first on Majanto.
A. to connect external Layer 3 networks to the SD-Access fabric B. to connect wired endpoints to the SD-Access fabric C. to advertise fabric IP address space to external networks D. to connect the fusion router to the SD-Access fabric Answer: Option B. Explanation: No answer description available for this question Show AnswerDiscussion The post In an SD-Access… Read More »
Refer to the exhibit. An engineer reconfigures the port-channel between SW1 and SW2 from an access port to a trunk and immediately notices this error in SW1’s log: *Mar 1 09:47:22.245: %PM-4-ERR_DISABLE: bpduguard error detected on Gi0/0, putting Gi0/0 in err-disable state Which command set resolves this error? A. SW1(config-if)#interface G0/0 SW1(config-if)#no spanning-tree bpdufilter SW1(config-if)#shut SW1(config-if)#no shut B.… Read More »
A. tunneling traffic from IPv6 to IPv4 VXLANs B. allowing encrypted communication on the local VXLAN Ethernet segment C. encapsulating and de-encapsulating VXLAN Ethernet frames D. tunneling traffic from IPv4 to IPv6 VXLANs Answer: Option C. Explanation: No answer description available for this question Show AnswerDiscussion The post Which action is a function of VTEP in VXLAN? appeared… Read More »
A. Stratum 0 B. Stratum 1 C. Stratum 14 D. Stratum 15 Answer: Option B. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr920/configuration/guide/bsm/16-6-1/b-bsm-xe-16-6-1-asr920/bsm-time-calendar-set.html Show AnswerDiscussion The post What NTP Stratum level is a server that is connected directly to an authoritative time source? appeared first on Majanto.