Category Archives: 300-510 Implementing Cisco Service Provider Advanced Routing Solutions (SPRI)

300-510 Implementing Cisco Service Provider Advanced Routing Solutions (SPRI) Question and Answers

After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?

Refer to the exhibit. After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely? A. The two routers cannot authenticate with one another. B. The two routers have the same area ID. C. The two routers have the same network… Read More »

After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?

Refer to the exhibit. After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration? A. Routes that have passed through AS 65517 have the local preference set to 150. B. Routes that have originated through AS 65517 have the local preference set to 150. C. Routes directly… Read More »

A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?

Refer to the exhibit. A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24? Answer: Option C. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A network operator… Read More »

R3 is: failing to accept multicast RP information from Domain-A advertising MSDP SA messages to R1 and R4 receiving SA messages only from R4 Which command must the engineer implement to resolve the issue?

Refer to the exhibit. R3 is: failing to accept multicast RP information from Domain-A advertising MSDP SA messages to R1 and R4 receiving SA messages only from R4 Which command must the engineer implement to resolve the issue? A. R3# ip msdp sa-filter in 192.168.3.1 B. R3# no ip msap sa-filter in 192.168.1.1 C. R3# no ip msdp… Read More »

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

A. traffic controller B. path computation engine C. tail-end router D. SNMP server Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology? appeared first… Read More »

CE1 is the gateway router into the provider network via PE1. A network operator must inject a default route into OSPF area 0. All devices inside area 0 must be able to reach PE1. Which configuration achieves this goal?

Refer to the exhibit. CE1 is the gateway router into the provider network via PE1. A network operator must inject a default route into OSPF area 0. All devices inside area 0 must be able to reach PE1. Which configuration achieves this goal? Answer: Option C. Explanation:  Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/47868-ospfdb9.html Show AnswerDiscussion The post CE1 is the gateway router… Read More »

Which task must you perform on interface g1/0/0 to complete the SSM implementation?

Refer to the exhibit. Which task must you perform on interface g1/0/0 to complete the SSM implementation? A. configure OSPFv3 B. enable CDP C. disable IGMP D. configure IGMPv3 Answer: Option D. Explanation:  Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16-book/imc-ssm.html Show AnswerDiscussion The post Which task must you perform on interface g1/0/0 to complete the SSM implementation? appeared first on Majanto.

Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?

A. ip pim bidir-enable B. ipv4 pim bidir-enable C. ip multicast-routing D. ip pim bidir Answer: Option A. Explanation:  Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-3s/imc-pim-xe-3s-book/imc_basic_cfg.html Show AnswerDiscussion The post Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware? appeared first on Majanto.

A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?

Refer to the exhibit. A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if… Read More »

An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?

Refer to the exhibit. An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken? A. Router 1 must have the keyword subnets included in the… Read More »