Tag Archives: engineer

An engineer must ensure that all traffic entering AS 200 from AS 100 chooses Link 2 as an entry point. Assume that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers. Which configuration accomplishes this task?

Refer to the exhibit. An engineer must ensure that all traffic entering AS 200 from AS 100 chooses Link 2 as an entry point. Assume that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers. Which configuration accomplishes this task? A. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path… Read More »

A network engineer must simplify the IPsec configuration by enabling IPsec over GRE using IPsec profiles. Which two configuration changes accomplish this? (Choose two).

Refer to the exhibit. A network engineer must simplify the IPsec configuration by enabling IPsec over GRE using IPsec profiles. Which two configuration changes accomplish this? (Choose two). A. Create an IPsec profile, associate the transform-set ACL, and apply the profile to the tunnel interface. B. Apply the crypto map to the tunnel interface and change the tunnel… Read More »

An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and an HTTP response code of 400. What do theseresponses tell the engineer?

Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and an HTTP response code of 400. What do these responses tell the engineer? A. The Accept header sent was application/xml. B. POST was used instead of PUT to… Read More »

An engineer attempts to configure a router on a stick to route packets between Clients, Servers, and Printers; however, initial tests show that this configuration is not working. Which command set resolves this issue?

Refer to the exhibit. An engineer attempts to configure a router on a stick to route packets between Clients, Servers, and Printers; however, initial tests show that this configuration is not working. Which command set resolves this issue? A. interface Vlan10 no ip vrf forwarding Clients !i nterface Vlan20 no ip vrf forwarding Servers !i nterface Vlan30 no… Read More »

An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration? A. All traffic will be policed based on access-list 120. B. If traffic exceeds the specified rate, it will be transmitted and remarked. C. Class-default traffic will be dropped. D. ICMP will be denied… Read More »

An engineer configures monitoring on SW1 and enters the show command to verify operation. What does the output confirm?

Refer to the exhibit. An engineer configures monitoring on SW1 and enters the show command to verify operation. What does the output confirm? A. RSPAN session 1 is incompletely configures for monitoring. B. RSPAN session 1 monitors activity on VLAN 50 of a remote switch. C. SPAN session 2 monitors all traffic entering and exiting port FastEthernet 0/15.… Read More »

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task?

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task? interface GigabitEthernet1/0/0 description To IDF A 38-70-774-10 ip address 172.16.13.2 255.255.255.0 A. standby 5 ip 172.16.13.254 standby 5 priority 100 standby… Read More »

A network engineer configures a new GRE tunnel and enters the show run command. What does the output verify?

Refer to the exhibit. A network engineer configures a new GRE tunnel and enters the show run command. What does the output verify? A. The tunnel keepalive is configured incorrectly because they must match on both sites. B. The tunnel destination will be known via the tunnel interface. C. The tunnel will be established and work as expected.… Read More »

An engineer must configure an ACL that permits packets which include an ACK in the TCP header. Which entry must be included in the ACL?

A. access-list 110 permit tcp any any eq 21 tcp-ack B. access-list 10 permit tcp any any eq 21 established C. access-list 110 permit tcp any any eq 21 established D. access-list 10 permit ip any any eq 21 tcp-ack Answer: Option C. Explanation:  No answer description available for this question Show AnswerDiscussion The post An engineer must… Read More »

A network engineer configures OSPF and reviews the router configuration. Which interface or interfaces are able to establish OSPF adjacency?

Refer to the exhibit. A network engineer configures OSPF and reviews the router configuration. Which interface or interfaces are able to establish OSPF adjacency? A. GigabitEthernet0/0 and GigabitEthernet0/1 B. only GigabitEthernet0/1 C. only GigabitEthernet0/0 D. GigabitEthernet0/1 and GigabitEthernet0/1.40 Answer: Option D. Explanation:  No answer description available for this question Show AnswerDiscussion The post A network engineer configures OSPF… Read More »