A. global configuration mode B. routing configuration mode C. BGP neighbor configuration D. mode BGP address-family configuration mode Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post Which CLI mode must be used to configure the BGP keychain in Cisco IOS XR software? appeared first on Majanto.
A. Change the HSRP group configuration on the local router to 1. B. Change the HSRP virtual address on the local routerto 10.1.1.1. C. Change the HSRP virtual address on the remote routerto 10.1.1.1. D. Change the HSRP group configuration on the remote routerto 1. Answer: Option B. Explanation: No answer description available for this question Show AnswerDiscussion… Read More »
A. standby version 2 standby 300 priority 110 standby 300 preempt B. standby 300 priority 110 standby 300 timers 1 110 C. standby version 2 standby 300 priority 90 standby 300 preempt D. standby 300 priority 90 standby 300 preempt Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post An engineer must… Read More »
A. NetFlow probe B. HTTP probe C. RADIUS probe D. network scan probe Answer: Option C. Explanation: Reference: https://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/200292Configure-Device-Sensor- for-ISE-Profilin.html Show AnswerDiscussion The post An engineer is implementing network access control using Cisco ISE and needs to separate the traffic based on the network device ID and use the IOS device sensor capability.<br> Which probe must be used… Read More »
A. peer-sync ipv4 192.168.0.3 B. state ipv4 192.168.0.3 C. peer ipv4 192.168.0.3 D. state-sync ipv4 192.168.0.3 Answer: Option D. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-2/segment-routing/configuration/guide/b-segment-routing-cg-asr9000-62x/b-seg-routing-cg-asr9000-62x_chapter_01001.html Show AnswerDiscussion The post Which command configures the remote peer when the Cisco IOS XR Traffic Controller is used? appeared first on Majanto.
A. source IP address, source port, encoding, and sampling interval B. source IP address, source port, encoding, and protocol C. destination IP address, destination port, encoding, and sensor path D. destination IP address, destination port, encoding, and protocol Answer: Option D. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/iosxr/asr9000/telemetry/b-telemetry-cg-asr9000-61x/b-telemetry-cg-asr9000-61x_chapter_010.html Show AnswerDiscussion The post An automation engineer is trying to configure a destination group… Read More »
An engineer wants to replace the BLOCK_BAD ACL on the Cisco IOS XE router with this new content. The engineer wants to use RESTCONF for this and constructs a PUT request to the resource/restconf/data/native/ip/access-list/ Cisco-IOS-XE-acl:extended=BLOCK_BAD. What must the body look like to achieve the Cisco IOS XE configuration? Desired configutation: ip access-list extended BLOCK_BAD permit ip any host… Read More »
A. The emsd process is not running. B. There are polling interval problems. C. SNMP is not enabled. D. There is no support for IOS XR 64-bit. Answer: Option A. Explanation: Reference: https://community.cisco.com/t5/service-providers-documents/implementing-grpc-telemetry-on-xr-devices/ta-p/3393966 Show AnswerDiscussion The post A user is debugging a problem with model-driven dial-in/out streams with gRPC for a Cisco IOS XR implementation. There is no… Read More »
A. show mpls forwarding-table B. show mpls ldp neighbors C. show mpls ldp labels D. show mpls ldp bindings Answer: Option A. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mpls/command/mp-cr-book/mp-s2.html Show AnswerDiscussion The post An engineer is investigating an MPLS LDP issue. Which command should an engineer use on a Cisco IOS XE device to display the contents of the LFIB? appeared first… Read More »
A. ip pim bidir-enable B. ipv4 pim bidir-enable C. ip multicast-routing D. ip pim bidir Answer: Option A. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-3s/imc-pim-xe-3s-book/imc_basic_cfg.html Show AnswerDiscussion The post Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware? appeared first on Majanto.