Tag Archives: needed

A Cisco engineer is implementing gRPC dial-out on an ASR. Receiver 192.168 1.1 will be assigned one of the subscriptions, and it will manage the ASR. Which command is needed to complete the router configuration?

Refer to the exhibit. A Cisco engineer is implementing gRPC dial-out on an ASR. Receiver 192.168 1.1 will be assigned one of the subscriptions, and it will manage the ASR. Which command is needed to complete the router configuration? A. protocol grpc B. protocol all C. protocol tcp D. protocol any Answer: Option C. Explanation: No answer description… Read More »

Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two.)

Refer to the exhibit. Which two commands are needed to allow for full reachability between AS 1000 and AS 2000? (Choose two.) A. R2#no network 10.0.0.0 255.255.255.0 B. R2#network 209.165.201.0 mask 255.255.192.0 C. R2#network 192.168.0.0 mask 255.255.0.0 D. R1#no network 10.0.0.0 255.255.255.0 E. R1#network 192.168.0.0 mask 255.255.0.0 Answer: Option A, C. Explanation: No answer description available for this… Read More »

A network is being migrated from IPv4 to IPv6 using a dual-stack approach. Network management is already 100% IPv6 enabled. In a dual-stack network with two dual-stack NetFlow collectors, how many flow exporters are needed per network device in the flexible NetFlow configuration?

A. 1 B. 2 C. 4 D. 8 Answer: Option B. Explanation: No answer description available for this question Show AnswerDiscussion The post A network is being migrated from IPv4 to IPv6 using a dual-stack approach. Network management is already 100% IPv6 enabled. <br>In a dual-stack network with two dual-stack NetFlow collectors, how many flow exporters are needed… Read More »

What is needed to configure wireless guest access on the network?

A. endpoint already profiled in ISE B. WEBAUTH ACL for redirection C. Captive Portal Bypass turned on D. valid user account in Active Directory Answer: Option C. Explanation: No answer description available for this question Show AnswerDiscussion The post What is needed to configure wireless guest access on the network? appeared first on Majanto.

An administrator is adding a switch to a network that is running Cisco ISE and is only for IP Phones. The phones do not have the ability to authenticate via 802.1X. Which command is needed on each switch port for authentication?

A. dot1x system-auth-control B. enable bypass-MAC C. enable network-authentication D. mab Answer: Option D. Explanation: No answer description available for this question Show AnswerDiscussion The post An administrator is adding a switch to a network that is running Cisco ISE and is only for IP Phones. The phones do not have the ability to authenticate via 802.1X. <br>Which… Read More »

Which two configurations are needed on a catalyst switch for it to be added as a network access device in a Cisco ISE that is being used for 802 1X authentications? (Choose two )

Refer to the exhibit. Which two configurations are needed on a catalyst switch for it to be added as a network access device in a Cisco ISE that is being used for 802 1X authentications? (Choose two ) A. Option A B. Option B C. Option C D. Option D E. Option E Answer: Option A, C. Explanation: … Read More »

An administrator is manually adding a device to a Cisco ISE identity group to ensure that it is able to access the network when needed without authentication Upon testing, the administrator notices that the device never hits the correct authorization policy line using the condition EndPoints LogicalProfile EQUALS static_list Why is this occurring?

A. The dynamic logical profile is overriding the statically assigned profile B. The device is changing identity groups after profiling instead ot remaining static C. The logical profile is being statically assigned instead of the identity group D. The identity group is being assigned instead of the logical profile Answer: Option C. Explanation: No answer description available for… Read More »

Which interface-level command is needed to turn on 802.1X authentication?

A. dot1x system-auth-control B. dot1x pae authenticator C. aaa server radius dynamic-author D. authentication host-mode single-host Answer: Option B. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/31sg/configuration/guide/conf/dot1x.html Show AnswerDiscussion The post Which interface-level command is needed to turn on 802.1X authentication? appeared first on Majanto.

What is needed to configure wireless guest access on the network?

After this operation, what else is needed to change the hostname of the router to IOS-XR-SJC-19?

Refer to the exhibit. After this operation, what else is needed to change the hostname of the router to IOS-XR-SJC-19? A. <confirm> B. <close-session> C. <get-config> D. <commit> Answer: Option D. Explanation: No answer description available for this question Show AnswerDiscussion The post After this operation, what else is needed to change the hostname of the router to… Read More »