Tag Archives: accomplish

An engineer must extend Layer 2 Between two campus sites connected through an MPLS backbone that encapsulates Layer 2 and Layer 3 data Which action must the engineer perform on the routers to accomplish this task?

A. Configure a EtherChannel for E-LAN. B. Configure a pseudowire for E-LINE. C. Configure Cisco MPLS TE for use with E-TREE. D. Configure QoS for MPLS and E-ACCESS Answer: Option B. Explanation:  No answer description available for this question Show AnswerDiscussion The post An engineer must extend Layer 2 Between two campus sites connected through an MPLS backbone… Read More »

A network operator has two IPv4 and IPv6 dual-stacked network on each side of the IPv4 core network. The operator must be able to provide connectivity between them while using specific assigned IPv6 space provided from the company IP administrator team. Which technology should the network operator use to accomplish this goal?

Refer to the exhibit. A network operator has two IPv4 and IPv6 dual-stacked network on each side of the IPv4 core network. The operator must be able to provide connectivity between them while using specific assigned IPv6 space provided from the company IP administrator team. Which technology should the network operator use to accomplish this goal? A. 6rd… Read More »

A network engineer is configuring RIP as the routing protocol between multiple PEs and CEs. The engineer must avoid advertising the same routes back to their sources. Which action should be performed on the routers to accomplish this task?

A. Configure a different route distinguisher for each prefix. B. Define the site of origin on each interface. C. Define VRFs on each device to separate the traffic. D. Enable bidirectional forwarding detection on each device. Answer: Option A. Explanation:  No answer description available for this question Show AnswerDiscussion The post A network engineer is configuring RIP as… Read More »

An engineer must assign an IP address of 192.168.1.1/24 to the GigabitEthernet1 interface. Which two commands must be added to the existing configuration to accomplish this task? (Choose two.)

Refer to the exhibit. An engineer must assign an IP address of 192.168.1.1/24 to the GigabitEthernet1 interface. Which two commands must be added to the existing configuration to accomplish this task? (Choose two.) A. Router(config-if)#ip address 192.168.1.1 255.255.255.0 B. Router(config-vrf)#address-family ipv4 C. Router(config-vrf)#ip address 192.168.1.1 255.255.255.0 D. Router(config-if)#address-family ipv4 E. Router(config-vrf)#address-family ipv6 Answer: Option A, D. Explanation:  No… Read More »

An engineer must configure interface GigabitEthernet0/0 for VRRP group 10. When the router has the highest priority in the group, it must assume the master role. Which command set must be added to the initial configuration to accomplish this task? Initial Configuration interface GigabitEthernet0/0 description To IDF A 38-24-044.40 ip address 172.16.13.2 255.255.255.0

A. standby 10 ip 172.16.13.254 255.255.255.0 standby 10 preempt B. vrrp group 10 ip 172.16.13.254 255.255.255.0 vrrp group 10 priority C. standby 10 ip 172.16.13.254 standy 10 priority 120 D. vrrp 10 ip 172.16.13.254 vrrp 10 preempt Answer: Option D. Explanation:  No answer description available for this question Show AnswerDiscussion The post An engineer must configure interface GigabitEthernet0/0… Read More »

A network engineer must simplify the IPsec configuration by enabling IPsec over GRE using IPsec profiles. Which two configuration changes accomplish this? (Choose two).

Refer to the exhibit. A network engineer must simplify the IPsec configuration by enabling IPsec over GRE using IPsec profiles. Which two configuration changes accomplish this? (Choose two). A. Create an IPsec profile, associate the transform-set ACL, and apply the profile to the tunnel interface. B. Apply the crypto map to the tunnel interface and change the tunnel… Read More »

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task?

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task? interface GigabitEthernet1/0/0 description To IDF A 38-70-774-10 ip address 172.16.13.2 255.255.255.0 A. standby 5 ip 172.16.13.254 standby 5 priority 100 standby… Read More »

What does this EEM applet event accomplish? “event snmp oid 1.3.6.1.3.7.6.5.3.9.3.8.7 get-type next entry-op gt entry-val 75 poll-interval 5”

A. Upon the value reaching 75%, a SNMP event is generated and sent to the trap server. B. It reads an SNMP variable, and when the value exceeds 75%, it triggers an action. C. It issues email when the value is greater than 75% for five polling cycles. D. It presents a SNMP variable that can be interrogated.… Read More »

Here’s A Paragraph From A Recap Email: “You Need To Get Into Your New Office Space Before The End Of This Quarter. You Have Aggressive Hiring Goals For Next Quarter And If You Haven’t Relocated Into A Larger Space By Then, You Won’t Be Able To Hit Those Goals. On The Other Hand, If You Get Into The Space You’re Currently Looking At, The Amenities Included In That Space Will Help You Attract New Talent.” Which Part Of The Explore Phase Does It Accomplish?

Here’s A Paragraph From A Recap Email: “You Need To Get Into Your New Office Space Before The End Of This Quarter. You Have Aggressive Hiring Goals For Next Quarter And If You Haven’t Relocated Into A Larger Space By Then, You Won’t Be Able To Hit Those Goals. On The Other Hand, If You Get Into The… Read More »