Tag Archives: configuring

What is used for cluster management and tot providing the API used for configuring and managing resources

What is used for cluster management and tot providing the API used for configuring and managing resources in a cluster created using Oracle Cloud Infrastructure Container Engine for Kubernetes (OKE)?Response: A. The master node is responsible for cluster management and for providing the API. B. The Cluster State Store is responsible for cluster management and for providing the… Read More »

An engineer working for a private service provider with employee id: 3994 37 650 is configuring a Cisco device to redistribute OSPF into BGP. Which task enables the device to filter routes?

A. Configure a distribute list and associate it to the BGP peer interface B. Configure a prefix list and associate it to the BGP peer interface C. Configure a route map and reference it with the redistribute command D. Configure an access list and reference it with the redistribute command Answer: Option C. Explanation: No answer description available… Read More »

A network engineer is configuring a newly installed PE router at the regional gateway location. The new PE router must use MPLS core routing protocols with the existing P router, and LDP sessions between the two routers must be protected to provide faster MPLS convergence. Which configuration must the engineer perform on the network so that LDP sessions are established?

A. Enable communication over TCP port 646 for T-LDP hello messages. B. Enable RSVP-TE FRR on the LDP interface to protect the LDP session between routers. C. Enable LDP session protection on either one of the routers, which allows them to autonegotiate. D. Set the LDP session protection timer on each router to the same value. Answer: Option… Read More »

A network engineer is configuring RIP as the routing protocol between multiple PEs and CEs. The engineer must avoid advertising the same routes back to their sources. Which action should be performed on the routers to accomplish this task?

A. Configure a different route distinguisher for each prefix. B. Define the site of origin on each interface. C. Define VRFs on each device to separate the traffic. D. Enable bidirectional forwarding detection on each device. Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post A network engineer is configuring RIP as… Read More »

An engineer is configuring an EtherChannel between Switch1 and Switch2 and notices the console message on Switch2. Based on the output, which action resolves this issue?

Refer to the exhibit. An engineer is configuring an EtherChannel between Switch1 and Switch2 and notices the console message on Switch2. Based on the output, which action resolves this issue? A. Configure more member ports on Switchl. B. Configure less member ports on Switch2. C. Configure the same port channel interface number on both switches. D. Configure the… Read More »

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task?

An engineer is configuring GigabitEthernet1/0/0 for VRRP. When the router has the highest priority in group 5, it must assume the master role. Which command set should the engineer add to the configuration to accomplish this task? interface GigabitEthernet1/0/0 description To IDF A 38-70-774-10 ip address 172.16.13.2 255.255.255.0 A. standby 5 ip 172.16.13.254 standby 5 priority 100 standby… Read More »

After configuring an IPsec VPN, an engineer enters the show command to verify the ISAKMP SA status. What does the status show?

Refer to the exhibit. After configuring an IPsec VPN, an engineer enters the show command to verify the ISAKMP SA status. What does the status show? A. VPN peers agreed on parameters for the ISAKMP SA. B. Peers have exchanged keys, but ISAKMP SA remains unauthenticated. C. ISAKMP SA is authenticated and can be used for Quick Mode.… Read More »

While configuring an IOS router for HSRP with a virtual IP of 10.1.1.1, an engineer sees this log message. Jan 1 12:12:12.111 : %HSRP-4-DIFFVIP1: GigabitEthernet0/0 Grp 1 active routers virtual IP address 10.1.1.1 is different to the locally configured address 10.1.1.25 Which configuration change must the engineer make?

A. Change the HSRP group configuration on the local router to 1. B. Change the HSRP virtual address on the local routerto 10.1.1.1. C. Change the HSRP virtual address on the remote routerto 10.1.1.1. D. Change the HSRP group configuration on the remote routerto 1. Answer: Option B. Explanation: No answer description available for this question Show AnswerDiscussion… Read More »

An engineer is configuring local web authentication on a WLAN. The engineer chooses the Authentication radio button under the Layer 3 Security options for Web Policy. Which device presents the web authentication for the WLAN?

A. ISE server B. RADIUS server C. anchor WLC D. local WLC Answer: Option D. Explanation: No answer description available for this question Show AnswerDiscussion The post An engineer is configuring local web authentication on a WLAN. The engineer chooses the Authentication radio button under the Layer 3 Security options for Web Policy.<br> Which device presents the web… Read More »

What are two components of the posture requirement when configuring Cisco ISE posture? (Choose two.)

A. Client Provisioning portal B. remediation actions C. updates D. access policy E. conditions Answer: Option B, E. Explanation: No answer description available for this question Show AnswerDiscussion The post What are two components of the posture requirement when configuring Cisco ISE posture? (Choose two.) appeared first on Majanto.