Tag Archives: configures

After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2:

Refer to the exhibit. After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2: SW2# 09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/0, putting Gi0/0 in err-disable state 09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/1, putting Gi0/1 in err-disable state Based on the output from switch SW1 and the… Read More »

An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration?

Refer to the exhibit. An engineer configures CoPP and enters the show command to verify the implementation. What is the result of the configuration? A. All traffic will be policed based on access-list 120. B. If traffic exceeds the specified rate, it will be transmitted and remarked. C. Class-default traffic will be dropped. D. ICMP will be denied… Read More »

An engineer configures monitoring on SW1 and enters the show command to verify operation. What does the output confirm?

Refer to the exhibit. An engineer configures monitoring on SW1 and enters the show command to verify operation. What does the output confirm? A. RSPAN session 1 is incompletely configures for monitoring. B. RSPAN session 1 monitors activity on VLAN 50 of a remote switch. C. SPAN session 2 monitors all traffic entering and exiting port FastEthernet 0/15.… Read More »

A network engineer configures a new GRE tunnel and enters the show run command. What does the output verify?

Refer to the exhibit. A network engineer configures a new GRE tunnel and enters the show run command. What does the output verify? A. The tunnel keepalive is configured incorrectly because they must match on both sites. B. The tunnel destination will be known via the tunnel interface. C. The tunnel will be established and work as expected.… Read More »

A network engineer configures OSPF and reviews the router configuration. Which interface or interfaces are able to establish OSPF adjacency?

Refer to the exhibit. A network engineer configures OSPF and reviews the router configuration. Which interface or interfaces are able to establish OSPF adjacency? A. GigabitEthernet0/0 and GigabitEthernet0/1 B. only GigabitEthernet0/1 C. only GigabitEthernet0/0 D. GigabitEthernet0/1 and GigabitEthernet0/1.40 Answer: Option D. Explanation:  No answer description available for this question Show AnswerDiscussion The post A network engineer configures OSPF… Read More »

An engineer configures a WLAN with fast transition enabled. Some legacy clients fail to connect to this WLAN. Which feature allows the legacy clients to connect while still allowing other clients to use fast transition based on their OUIs?

A. over the DS B. 802.11k C. adaptive R D. 802.11v Answer: Option C. Explanation:  No answer description available for this question Show AnswerDiscussion The post An engineer configures a WLAN with fast transition enabled. Some legacy clients fail to connect to this WLAN.<br> Which feature allows the legacy clients to connect while still allowing other clients to… Read More »

Which command configures the remote peer when the Cisco IOS XR Traffic Controller is used?

A. peer-sync ipv4 192.168.0.3 B. state ipv4 192.168.0.3 C. peer ipv4 192.168.0.3 D. state-sync ipv4 192.168.0.3 Answer: Option D. Explanation:  Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-2/segment-routing/configuration/guide/b-segment-routing-cg-asr9000-62x/b-seg-routing-cg-asr9000-62x_chapter_01001.html Show AnswerDiscussion The post Which command configures the remote peer when the Cisco IOS XR Traffic Controller is used? appeared first on Majanto.

An engineer configures a Cisco Aironet 600 Series OfficeExtend AP for a user who works remotely. What is configured on the Cisco WLC to allow the user to print a printer on his home network?

A. split tunneling B. SE-connect C. FlexConnect D. AP failover priority Answer: Option A. Explanation:  Reference: https://www.cisco.com/c/en/us/support/docs/wireless/aironet-602-officeextend-access-point/117540-configure-splittunneloeap-00.html Show AnswerDiscussion The post An engineer configures a Cisco Aironet 600 Series OfficeExtend AP for a user who works remotely. What is configured on the Cisco WLC to allow the user to print a printer on his home network? appeared first… Read More »

An engineer configures a deployment to support:Cisco CMX licenses for at least 3000 APs 6000 wIPS licenses The Cisco vMSE appliance must be sized for this deployment. Which Cisco vMSE Release 8 option must the engineer deploy?

A. Large vMSE B. Low-End vMSE C. Standard vMSE D. High-End vMSE Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post An engineer configures a deployment to support:<br>Cisco CMX licenses for at least 3000 APs 6000 wIPS licenses The Cisco vMSE appliance must be sized for this deployment. Which Cisco vMSE Release… Read More »

An engineer configures the wireless LAN controller to perform 802.1x user authentication. Which configuration must be enabled to ensure that client devices can connect to the wireless, even when WLC cannot communicate with the RADIUS?

A. pre-authentication B. local EAP C. authentication caching D. Cisco Centralized Key Management Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post An engineer configures the wireless LAN controller to perform 802.1x user authentication. Which configuration must be enabled to ensure that client devices can connect to the wireless, even when WLC… Read More »