Tag Archives: WLC

What is the responsibility of a secondary WLC?

A. It enables Layer 2 and Layer 3 roaming between itself and the primary controller. B. It registers the LAPs if the primary controller fails. C. It avoids congestion on the primary controller by sharing the registration load on the LAPs. D. It shares the traffic load of the LAPs with the primary controller. Answer: Option A. Explanation: … Read More »

In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one AP to another on a different access switch using a single WLC?

A. Layer 3 B. inter-xTR C. auto anchor D. fast roam Answer: Option D. Explanation:  No answer description available for this question Show AnswerDiscussion The post In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one AP to another on a different access switch using a single WLC? appeared first on… Read More »

Assuming the WLC’s interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic?

Refer to the exhibit. Assuming the WLC’s interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic? A. the controller management interface B. the controller virtual interface C. the interface specified on the WLAN configuration D. any interface configured on the WLC Answer: Option… Read More »

What sends the redirect ACL that is configured in the authorization profile back to the Cisco WLC?

A. State attribute B. Class attribute C. Event D. Cisco-av-pair Answer: Option D. Explanation:  Reference: https://community.cisco.com/t5/network-access-control/ise-airespace-acl-wlc-problem/td-p/2110491 Show AnswerDiscussion The post What sends the redirect ACL that is configured in the authorization profile back to the Cisco WLC? appeared first on Majanto.

An engineer must configure a Cisco WLC to support Cisco Aironet 600 Series OfficeExtend APs. Which two Layer 2 security options are supported in this environment? (Choose two.)

A. Static WEP + 802.1X B. WPA+WPA2 C. Static WEP D. CKIP E. 802.1X Answer: Option B, C. Explanation:  No answer description available for this question. Show AnswerDiscussion The post An engineer must configure a Cisco WLC to support Cisco Aironet 600 Series OfficeExtend APs. Which two Layer 2 security options are supported in this environment? (Choose two.)… Read More »

An engineer configures a Cisco Aironet 600 Series OfficeExtend AP for a user who works remotely. What is configured on the Cisco WLC to allow the user to print a printer on his home network?

A. split tunneling B. SE-connect C. FlexConnect D. AP failover priority Answer: Option A. Explanation:  Reference: https://www.cisco.com/c/en/us/support/docs/wireless/aironet-602-officeextend-access-point/117540-configure-splittunneloeap-00.html Show AnswerDiscussion The post An engineer configures a Cisco Aironet 600 Series OfficeExtend AP for a user who works remotely. What is configured on the Cisco WLC to allow the user to print a printer on his home network? appeared first… Read More »

A corporation is spread across different countries and uses MPLS to connect the offices. The senior management wants to utilize the wireless network for all the employees. To ensure strong connectivity and minimize delays, an engineer needs to control the amount of traffic that is traversing between the APs and the central WLC. Which configuration should be used to accomplish this goal?

A. FlexConnect mode with central switching enabled B. FlexConnect mode with central authentication C. FlexConnect mode with OfficeExtend enabled D. FlexConnect mode with local authentication Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A corporation is spread across different countries and uses MPLS to connect the offices. The senior management wants… Read More »

When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN ID of 30 to a FlexConnect group named BranchA-FCG?

A. config flexconnect BranchA-FCG vlan 30 add B. config flexconnect BranchA-FCG vlan add 30 C. config flexconnect group BranchA-FCG vlan 30 add D. config flexconnect group BranchA-FCG vlan add 30 Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post When configuring a Cisco WLC, which CLI command adds a VLAN with VLAN… Read More »

A FlexConnect remote office deployment is using five 2702i APs indoors and two 1532i APs outdoors. When a code upgrade is performed and FlexConnect Smart AP Image Upgrade is leveraged, but no FlexConnect Master AP has been configured, how many image transfers between the WLC and APs will occur?

A. 1 B. 2 C. 5 D. 7 Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A FlexConnect remote office deployment is using five 2702i APs indoors and two 1532i APs outdoors. When a code upgrade is performed and FlexConnect Smart AP Image Upgrade is leveraged, but no FlexConnect Master AP… Read More »

On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection to the WLC, all clients are disconnected, and the SSID is no longer advertised. Considering that FlexConnect local switching is enabled, which setting is causing this behavior?

A. ISE NAC is enabled B. 802.11r Fast Transition is enabled C. Client Exclusion is enabled D. FlexConnect Local Auth is disabled Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection… Read More »