Which two are true about instance recovery for a database that is open in read write mode?(Choose two.) A. It is always performed when opening a database. B. The database opens after the roll forward phase of instance recovery has completed. C. It is guaranteed to complete within fast_start_mttr_target number of seconds. D. Only the CURRENT REDO log… Read More »
Which two are true about instance recovery for a database that is open in read write mode?(Choose two.) A. Only the CURRENT REDO log group is required to perform instance recovery. B. The database opens after the roll forward phase of instance recovery has completed. C. It always occurs during instance startup performed immediately after a SHUTDOWN ABORT.… Read More »
A. global configuration mode B. routing configuration mode C. BGP neighbor configuration D. mode BGP address-family configuration mode Answer: Option A. Explanation: No answer description available for this question Show AnswerDiscussion The post Which CLI mode must be used to configure the BGP keychain in Cisco IOS XR software? appeared first on Majanto.
Drag and drop the characteristics of PIM Dense Mode from the left to the right. Not all options are used. Select and Place: Answer: Explanation: No answer description available for this question Show AnswerDiscussion The post Drag and drop the characteristics of PIM Dense Mode from the left to the right. Not all options are used. appeared first… Read More »
A. APs that operate in FlexConnect mode cannot detect rogue APs. B. When connected to the controller, FlexConnect APs can tunnel traffic back to the controller. C. FlexConnect mode is used when the APs are set up in a mesh environment and used to bridge between each other. D. FlexConnect mode is a feature that is designed to… Read More »
A. tap B. inline C. passive D. inline tap Answer: Option B. Explanation: Reference: https://www.cisco.com/c/en/us/support/docs/security/firepower-ngfw/200924-configuring-firepower-threat-defense-int.html Show AnswerDiscussion The post Which NGFW mode blocks flows crossing the firewall? appeared first on Majanto.
A. inter-controller B. inter-subnet C. intra-VLAN D. intra-controller Answer: Option D. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-3/config-guide/b_cg83/b_cg83_chapter_010011.html Show AnswerDiscussion The post A client device roams between access points located on different floors in an atrium. The access points are joined to the same controller and configured in local mode. The access points are in different AP groups and have different IP… Read More »
A. closed B. high-impact C. low-impact D. open Answer: Option C. Explanation: Reference: https://community.cisco.com/t5/security-documents/ise-secure-wired-access-prescriptivedeployment-guide/ta- p/3641515 Show AnswerDiscussion The post An engineer is configuring 802.1X and wants it to be transparent from the users’ point of view. The implementation should provide open authentication on the switch ports while providing strong levels of security for non-authenticated devices.<br> Which deployment mode… Read More »
A. DNS B. DHCP C. EAP D. HTTP Answer: Option D. Explanation: No answer description available for this question Show AnswerDiscussion The post An engineer is using the low-impact mode for a phased deployment of Cisco ISE and is trying to connect to the network prior to authentication.<br>Which access will be denied in this deployment? appeared first on… Read More »
A. ip pim bidir-enable B. ipv4 pim bidir-enable C. ip multicast-routing D. ip pim bidir Answer: Option A. Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-3s/imc-pim-xe-3s-book/imc_basic_cfg.html Show AnswerDiscussion The post Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware? appeared first on Majanto.