Tag Archives: Controllers

A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers. Which protocol must be allowed to reach the MSE from the controllers?

A. SOAP/XML B. NMSP C. CAPWAP D. SNMP Answer: Option A. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers. Which protocol must be allowed to reach the MSE from the controllers? appeared first… Read More »

An engineer must configure the virtual IP address on multiple controllers in a mobility group. Which rule must the engineer follow to ensure proper roaming?

A. Ensure that the DNS entry is tied to the virtual IP address of the WLC. B. Use a unique IP address for each WLC. C. Ensure that the DNS Host Name field is defined. D. Use the same IP address for each WLC. Answer: Option A. Explanation:  No answer description available for this question. Show AnswerDiscussion The… Read More »

A customer has two Cisco 550B WLCs that manage all the access points in their network and provide N+1 redundancy and load balancing. The primary Cisco WLC has 60 licenses and the secondary Cisco WLC has 40. The customer wants to convert the N+1 model to an HA model and provide SSO. Configuration must be performed during a maintenance window. After performing all the configurations on both controllers, the config redundancy unit secondary command is issued on the secondary Cisco WLC and it fails. Which parameter needs to be in place to complete the configuration?

A. A cable in the RP port B. The secondary Cisco WLC needs a minimum of 50 base licenses C. The primary Cisco WLC is already set as the secondary unit. D. SSO needs to be enabled Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A customer has two Cisco 550B… Read More »

A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet.

Refer to the exhibit. A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet. Both controllers are running AireOS. Which scenario explains the client roaming behavior? A. Controllers exchange mobility control messages (over UDP port 16666), and the client database entry is moved from the… Read More »

Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?

A. rping B. ping C. eping D. mping Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected? appeared first on Majanto.

A network engineer is configuring high availability on an access point. What is the maximum number of controllers available to be configured?

A. 1 B. 2 C. 3 D. 4 Answer: Option B. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A network engineer is configuring high availability on an access point. What is the maximum number of controllers available to be configured? appeared first on Majanto.

Two Cisco 5520 Wireless LAN Controllers are managing all access points throughout the network. The WLCs are in different locations to provide geographical redundancy. A mobility group has been configured on both WLCs and has an UP status on both controllers. The APs in location A are statically configured to use controller A as the primary and controller B as the secondary. If the WLC in location A goes offline, the APs successfully join the WLC in location B, but they do not fail over to the primary configured controller. Which configuration task fixes this issue?

A. Enable AP fallback globally on the WLC. B. Change the AP Failover Priority to critical. C. Use DHCP Option 43 and specify WLC in location A as primary. D. Configure the WLC in location A as primary using the CAPWAP AP Controller IP Address command on all the location A access points. Answer: Option A. Explanation:  No… Read More »

Which mode allows access points to be managed by Cisco Wireless LAN Controllers?

A. bridge B. lightweight C. mobility express D. autonomous Answer: Option B. Explanation:  Section: Network Access A Lightweight Access Point (LAP) is an AP that is designed to be connected to a wireless LAN (WLAN) controller (WLC). APs are “lightweight,” which means that they cannot act independently of a wireless LAN controller (WLC). The WLC manages the AP… Read More »