Tag Archives: subnet

An engineer must block all traffic from a router to its directly connected subnet 209.165.200.0/24. The engineer applies access control list EGRESS in the outbound direction on the GigabitEthernet0/0 interface of the router. However, the router can still ping hosts on the 209.165.200.0/24 subnet. Which explanation of this behavior is true?

Refer to the exhibit. An engineer must block all traffic from a router to its directly connected subnet 209.165.200.0/24. The engineer applies access control list EGRESS in the outbound direction on the GigabitEthernet0/0 interface of the router. However, the router can still ping hosts on the 209.165.200.0/24 subnet. Which explanation of this behavior is true? A. Access control… Read More »

Which standard access control entry permits traffic from odd-numbered hosts in the 10.0.0.0/24 subnet?

A. permit 10.0.0.0 0.0.0.1 B. permit 10.0.0.1 0.0.0.254 C. permit 10.0.0.1 0.0.0.0 D. permit 10.0.0.0 255.255.255.254 Answer: Option B. Explanation:  No answer description available for this question Show AnswerDiscussion The post Which standard access control entry permits traffic from odd-numbered hosts in the 10.0.0.0/24 subnet? appeared first on Majanto.

An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound direction on router interface GigabitEthernet 0/1. Which configuration command set will allow this traffic without disrupting existing traffic flows?

Refer to the exhibit. An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound direction on router interface GigabitEthernet 0/1. Which configuration command set will allow this traffic without disrupting existing traffic flows? Answer: Option D. Explanation:  No answer description… Read More »

Assuming the WLC’s interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic?

Refer to the exhibit. Assuming the WLC’s interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic? A. the controller management interface B. the controller virtual interface C. the interface specified on the WLAN configuration D. any interface configured on the WLC Answer: Option… Read More »

A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet.

Refer to the exhibit. A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet. Both controllers are running AireOS. Which scenario explains the client roaming behavior? A. Controllers exchange mobility control messages (over UDP port 16666), and the client database entry is moved from the… Read More »

EIGRP has been configured on all links. The spoke nodes have been configured as EIGRP stubs, and the WAN links to R3 have higher bandwidth and lower delay than the WAN links to R4. When a link failure occurs at the R1-R2 link, what happens to traffic on R1 that is destined for a subnet attached to R2?

Refer to the exhibit. EIGRP has been configured on all links. The spoke nodes have been configured as EIGRP stubs, and the WAN links to R3 have higher bandwidth and lower delay than the WAN links to R4. When a link failure occurs at the R1-R2 link, what happens to traffic on R1 that is destined for a… Read More »

A customer requests a VPN solution to connect multiple sites with the company headquarters. All the sites use the same IP subnet. The engineer plans to use VPLS. Which solution must the engineer include in the design?

A. different VLANs on each site B. address translation to hide overlapping subnets C. 802.1Q connectivity on the LAN side of the CE D. route exchange with the service provider Answer: Option C. Explanation:  No answer description available for this question. Show AnswerDiscussion The post A customer requests a VPN solution to connect multiple sites with the company… Read More »

An engineer must configure a /30 subnet between two routes. Which usable IP address and subnet mask combination meets this criteria?

A. interface e0/0 description to XX-AXXX:XXXXX ip address 10.2.1.3 255.255.255.252 B. interface e0/0 description to XX-AXXX:XXXXX ip address 192.168.1.1 255.255.255.248 C. interface e0/0 description to XX-AXXX:XXXXX ip address 172.16.1.4 255.255.255.248 D. interface e0/0 description to XX-AXXX:XXXXX ip address 209.165.201.2 225.255.255.252 Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post An engineer must… Read More »

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

A. B. C. D. Answer: Option D. Explanation:  No answer description available for this question. Show AnswerDiscussion The post An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used? appeared first on Majanto.